DIALux Simulation for Architectural Facade Lighting

By the MEKALEO engineering team — 22 years of LED facade production since 2004

Executive Summary

  • A credible DIALux study begins with a clean geometric model, verified photometric files, realistic surface reflectance, and documented observer viewpoints.
  • Use illuminance, luminance, uniformity, glare, spill light, and energy results together; no single metric describes a facade experience.
  • Simulation is a design decision tool and must be followed by aiming checks, night-time measurement, and commissioning records.

1. Build a traceable simulation model

Start by importing or rebuilding the relevant facade geometry at a controlled scale. Remove hidden geometry that does not influence light, but preserve balconies, fins, parapets, glazing, and adjacent surfaces that can create reflections or shadowing. Record coordinate origin, north direction, units, material reflectance, transmittance, and the revision of every luminaire file.

Photometric inputs

Use manufacturer IES or EULUMDAT files that match the proposed optic, drive current, colour temperature, and dimming state. Check whether the file represents absolute lumens or a relative distribution. Confirm the photometric centre, tilt convention, beam angle, lumen maintenance assumption, and any built-in glare shield. For architectural linear lighting the file must be measured on the actual extrusion and lens combination, not a generic 1 m sample. A beautiful render made with the wrong optic is not an engineering result.

Four hand-over points of a traceable DIALux simulation with an illuminance grid A traceable simulation has four hand-over points 1. Geometry massing, glazing, fins, obstructions 2. Photometry exact IES/LDT files, drive state, ageing 3. Calculation grid spacing, observer viewpoints 4. Verification site measurement, acceptance record Illuminance grid, 4 m spacing 150 167 183 183 167 150 150 167 183 183 167 150 lux on the reference plane cells below the label threshold Report U₀, U₁ and the max/min ratio per zone — a single average hides the dark bands a client will notice. Keep the grid, the observer points and the photometric file version in the report so the result can be re-checked.
Four hand-over points of a traceable simulation, with the illuminance grid that has to accompany the report.

2. Core equations and worked example

For a point-source screening calculation, E = I cos(theta) / d², where E is illuminance in lux, I is luminous intensity in candela, theta is the incidence angle, and d is distance in metres. If a luminaire produces 4,000 cd toward a wall point 12 m away at 20 degrees, E = 4,000 x cos(20 degrees) / 12² = 29.3 lux. DIALux accounts for the full photometric distribution, multiple sources, reflections, and calculation grids, so the point-source result is a reasonableness check rather than the final answer.

Uniformity can be expressed as U0 = Emin / Eavg. If a facade grid reports Emin = 18 lux and Eavg = 30 lux, U0 = 0.60. State the grid spacing and whether the calculation excludes boundary points. For luminance, relate reflected light to surface luminance using the selected material model and photometric engine; do not convert lux to cd/m² with an assumed reflectance unless that assumption is documented.

Glare and spill-light checks

Set observer positions for pedestrians, drivers, neighbouring properties, and upper floors. Review high-intensity directions, direct line of sight to LED apertures, reflected glare from glazing, and light trespass beyond the property line. Control glare with shielding, tilt limits, lower night-time output, warmer colour temperature where appropriate, and scene-based dimming.

3. Simulation parameter comparison

ParameterConcept studyTender or approval studyAcceptance check
GeometrySimplified massingCoordinated facade modelAs-built survey
PhotometryRepresentative distributionExact product file and drive stateAiming and output verification
Calculation gridCoarse visual gridDefined spacing and boundariesCalibrated measurement points
ScenariosNormal and festiveAll operating scenes and curfewsNight commissioning scenes

4. From simulation to site

Freeze luminaire coordinates, tilt, mounting height, circuit ID, control address, and scene level in the schedule. During aiming, verify one reference zone before repeating the setting across the facade. Measure with a calibrated lux meter or luminance camera suited to the task and record ambient conditions, exposure settings, and measurement uncertainty. Compare the result to the approved calculation with the same grid and scene level.

For media facades, combine the photometric study with a pixel pitch and viewing-distance assessment. For power and control coordination, see the DMX addressing and commissioning guide.

💡 Engineering Tip

Save one simulation file per design revision and embed a calculation report date, luminaire-file checksum, and scene name in the exported PDF. This prevents an old photometric file from being mistaken for the approved design.

⚠️ Caution

Do not claim compliance from a rendered image. A render can hide clipping, saturated colours, glare, and boundary conditions. Approval should rely on traceable calculation outputs and field measurements.

5. FAQ

What is the most common simulation error?

Using an approximate or mismatched photometric file. The second most common is an unrealistic surface material or missing obstruction that changes the light path.

How fine should a facade calculation grid be?

It should resolve the smallest important lighting feature and the relevant approval area. State the spacing and perform a sensitivity check so a bright or dark narrow band is not averaged away.

Can DIALux predict glare from media pixels?

It can support the analysis when the source distribution and observer geometry are represented correctly, but high-dynamic-range pixel content requires scene-specific luminance review and field validation.

Related engineering guides

References & Standards

Need a review-ready lighting simulation?

Send the elevation model, luminaire files, observer locations, operating scenes, and approval criteria. We can prepare a traceable simulation package and a field verification plan.

Request a Simulation Review

Project enquiry

Send your drawings. Get a specification you can defend.

Elevation DWG, facade area, closest viewing distance and site country — we reply within 48 hours with a fixture matrix, power and DMX topology, and a quotation. No price-only quotes.

5,000+ projects delivered · 40+ countries · ISO 9001 · CE / UL / RoHS

About the publisher

MEKALEO is the export brand of Guangdong Meidile Technology Lighting Co., Ltd., a manufacturer of outdoor LED facade lighting and LED media facades. Founded in 2004, the company has worked on exterior architectural LED systems for 22 years and runs its own 8,000 m² factory in Guzhen, Zhongshan, China, with in-house SMT, vacuum potting and an IP test chamber. To date: 5,000+ delivered projects across 40+ countries, 100+ patents, ISO 9001, and CE / UL / RoHS certified products.

About us · Talk to an engineer

GET A QUICK QUOTE ↗

Related Articles

Get a Quote for Outdoor Lighting