Key Takeaways
An LED wall washer is optimized for even vertical illumination with asymmetric optics, while a floodlight is a higher-output projector for broad or long-throw coverage. Select the optic from facade geometry, viewing distance and glare limits—not wattage alone. A 1:3 setback starting rule, U0 ≥ 0.4 vertical uniformity target and DIALux verification create a defensible design.
1. What Each Luminaire Does
Wall washer
Wall washers use asymmetric lenses such as 10×60° or 15×45° to push light up the facade and reduce spill behind the fixture. They suit continuous stone, curtain-wall mullions and hotel elevations where uniform brightness is more important than a concentrated hot spot. Anti-glare honeycomb louvers and snoots control views from streets and neighboring buildings.
Floodlight
Floodlights generally use symmetrical narrow-to-wide beams from approximately 3° to 60°. A 3–10° beam reaches crowns and columns over long distances; 25–60° beams cover plazas, setbacks and large building planes. Adjustable brackets, optical shields and aiming limits are essential to prevent sky glow.
2. Beam Angle, Setback and Uniformity
The 1:3 setback rule
As an initial layout, set fixture setback at roughly one-third of the illuminated height. For a 12 m wall, begin near 4 m, then optimize spacing and tilt in simulation. The rule is a starting point, not a substitute for photometric data: facade reflectance, window mullions and fixture height can change the result.
Vertical illuminance target
Evaluate average and minimum vertical illuminance on a grid. A practical architectural target is U0 = Emin/Eavg ≥ 0.4 for a visually consistent wall, with tighter criteria for premium media environments. Check maximum luminance, spill to windows, pedestrian eye-level glare and color consistency at multiple viewing angles.
DIALux workflow
- Import the elevation and surrounding obstructions.
- Set facade reflectance, maintenance factor and target CCT.
- Load the manufacturer IES/LDT file for the actual lens and louver.
- Test mounting height, spacing, tilt and dimming scenes.
- Review vertical illuminance, uniformity, glare and spill before issuing drawings.
3. Professional Specification Comparison
| Criterion | LED wall washer | LED floodlight | Recommended application |
|---|---|---|---|
| Typical optics | 10×60°, 15×45° asymmetric | 3°, 10°, 25°, 40°, 60° symmetric | Choose based on wall depth and throw |
| Primary goal | Uniform vertical wash | High-output projection | Washer for planes; floodlight for accents |
| Glare control | Honeycomb louver, visor | Snoot, shield, visor | Specify accessories with the optic |
| Spacing | Closer, overlapping beams | Wider or long-throw grid | Validate in DIALux |
| Control | DMX512/RDM or on-off | DMX512/RDM or on-off | Use scenes and night dimming |
4. Selection Checklist
Specify output, CRI, CCT, IP/IK rating, beam file, louver, mounting bracket, corrosion finish and control protocol. On coastal projects, require marine-grade coating and stainless hardware. Aim fixtures away from bedrooms and roads, provide service access, and commission at nighttime with lux-meter readings against the model.
See our LED facade product range, project engineering support, and the related architectural LED linear light range.
Related engineering guides
- Architectural LED linear light installation guide
- 3D point-light matrix vs linear lighting for curved facades
- DIALux simulation for wall-washer uniformity checks
- LED flood light specifications
Frequently Asked Questions
When should I use a wall washer instead of a floodlight?
Use a wall washer when the objective is even vertical brightness on a continuous surface. Use a floodlight for long throw, crowns, columns, landscape zones or adjustable accenting.
What does 10×60° mean?
It describes an asymmetric beam: approximately 10° in the narrow distribution and 60° in the wide distribution. The narrow axis controls throw while the wide axis spreads light across the wall.
Is U0 ≥ 0.4 mandatory?
It is a useful project target, not a universal code requirement. The lighting designer should confirm the applicable local standard and the owner’s visual-quality brief.
Why is DIALux necessary?
It predicts overlap, shadowing, spill and uniformity using the real photometric file, helping avoid expensive aiming changes after installation.
References & Industry Standards
For project specifications, compliance review and procurement verification, consult these official industry sources:
Project enquiry
Send your drawings. Get a specification you can defend.
Elevation DWG, facade area, closest viewing distance and site country — we reply within 48 hours with a fixture matrix, power and DMX topology, and a quotation. No price-only quotes.
5,000+ projects delivered · 40+ countries · ISO 9001 · CE / UL / RoHS



